Advantek Networks AWR-854G Manuale Utente

Wireless LAN 802.11g/b, 54Mbps/2.4GHz Broadband Router with Firewall Support Model # : AWR-854G User’s Manual

9 b) Click “Properties”, the window below will appear: • If you decide to use DHCP, select “Obtain an IP address automatically”, then click “OK”

10 d) Select “DNS Configuration” tab and make sure select “Enable DNS”, enter the DNS address provides from your ISP in the “DNS Server Search Ord

11 Checking TCI/IP Setting for Windows NT4.0 a) Select “Control Panel Æ Network”, click “Protocols” tab then select “TCP/IP protocol”, window shown

12 b) Click “Properties”, window shown as below will appear.

13 • Select the network card on your system from “Adapter” field. • If you decide to use IP address from Wireless Router, select “Obtain an IP addr

14 Checking TCP/IP Settings for Windows 2000 a) Select “Start Æ Control Panel Æ Network and Dial-up Connection” and right click “Local Area Connect

15 b) Select the “Internet Protocol (TCP/IP)” for the network card on your system, then click “Properties”, window shown as below will appear.

16 • If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. • If you decide to use the IP address you a

17 b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window shown as below will appear.

18 • If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. • If you decide to use the IP address you

1FCC Warning This device is intended to use under the following conditions: 1) The antenna must be installed such that 20cm is maintained between

19c) Select “I want to set up my Internet connection manually, or I want to connect through a local area network (LAN)” then click “Next”. d) Select

20 Most Linux installations use fixed IP address, if you wish to use a fixed IP address, make sure make the following changes. a) Set “Default Gatew

213. Setup Wireless Router Configurations via Web Browser The Wireless Router comes with a web-based configuration utility. Users can

223.2 System This section displays the basic configuration parameters of your Wireless Router, such as System Status, System Settings, Administrator

23 INTERNET: Displays WAN connection type and status. GATEWAY: Displays system IP settings, as well as DHCP, NAT and Firewall status. INFORMATION: Di

24 Host Name: Enter a hostname if it was provided by the ISP (Default: Wireless_Router). Domain Name: Enter a Domain Name if it was provided by the I

25local network. However, you can also manage the Wireless Broadband Router from a remote host by adding the IP address of an administrator to this s

26 Firmware Upgrade: This tool allows you to upgrade the Broadband router’s system firmware. To upgrade the firmware of your Broadband router, you ne

27 Restart System: Reset Wireless Broadband Router, Reboot this device. Restore Factory Defaults: Reset the settings of this device to the factory de

28 System Log: Wireless broadband router’s system activity. Security Log: Displays any illegal attempts to access your network. 3.3 WAN Connected T

2 Table of Contents 1 Introduction ………………………………………….………………...3 1.1 Features ……………………………………………………………..…….4 1.2 Package Contents ………………………………

29 Dynamic IP address: Your ISP will automatically give you an IP address Static IP address: Your ISP has given you an IP address already PPPoE: Your

30DNS Domain Name Servers are used to map an IP address to the equivalent domain name (e.g.www.waveplus.com). Your ISP should provide the IP addres

31Valid IP addresses consist of four numbers, and are separated by periods. The first three fields are the network portion, and can be from 0-255, wh

32DHCP Client List The DHCP client list allows you to see which clients are connected to the Wireless Broadband Router via IP address, host name, a

333.5 NAT Virtual Server If you configure the Wireless Broadband Router as a virtual server, remote users accessing services such as Web or FTP a

34number will be changed to when the packet enters your LAN (to the LAN Server/Client IP) Type: Select the port number protocol type (TCP, UDP or bot

35 Trigger Port: This is the out going (Outbound) range of port numbers for this particular application. Trigger Type: Select whether the outbound po

36 Server IP: Enter the NAT server IP address. Mapping Ports: Enter the port address NAT server maps to. Type: Select the Inbound port protocol type:

37 ALG (Application Layer Gateway): You can select to enable, then the router will let that application correctly pass though the NAT gateway. DMZ (

38 DMZ (Demilitarized Zone): Enable/disable DMZ. Public IP Address: The IP address of the WAN port or any other Public IP addresses given to you by y

3 1. Introduction Thank you for purchasing Advantek Networks AWR-854G Wireless 11g/b Broadband Router. This Wireless Broadband Router is IEEE802

39 Firewall Options: Select the functions that firewall supports. The selections include Enable Hacker Attack Protect, Discard PING from WAN side,

40 URL Filtering To configure the URL Filtering feature, use the table as above to specify the web sites (www.somesite.com) and/or web URLs contai

41 MAC Control The MAC Control window allows user to block certain client PCs accessing the Internet based on MAC address.

42 MAC Address Control: This function allows user to determine whether to filter out or accept the following MAC address connect to Internet. Configu

43 Static Routing A static route is a pre-determined pathway that network information must travel to reach a specific host or network. Destinatio

44Gateway: The next stop gateway of the path toward the destination LAN. This is the IP of the neighbor router that this router should communicate wi

45vendors that cooperate in the Plug and Play forum. UPnP Settings: You can Enable or Disable UPnP feature here. Port Mapping The Port Mappings w

46 3.9 DDNS DDNS Dynamic DNS) DDNS (Dynamic DNS) provides you on the Internet with a method to tie their domain name to a computer or server. DDNS

47 DDNS: Enable/Disable the DDNS function of this router. 3.10 Wireless Basic Configuration The Basic Configuration window allows user to set wirel

48 SSID: SSID (Service Set Identifier) is the network name (by default: Default_11G). It is case-sensitive and must not exceed 32 characters. To comm

4 1.1 Features Internet Access Features • Shared Internet Access: All users on the LAN or WLAN can access the Internet through the Wireless Router

49 WEP Encryption: You may disable or enable the WEP function from the setting item. The selections in the setting item are changed based on the key

50DTIM Period, Basic Rate Set, TX Rates and Preamble. Regulatory Domain: Allows user to select the region wireless broadband router is located. Th

51Preamble: Either Short (72 bits) or Long (144 bits). MAC Filter The MAC Filter window allows user to set wireless broadband router to allow/prev

52 Authentication The Authentication Setting window allows user to set up wireless security settings, such as Security Mode, WPA-PSK Pass Phrase,

53 Security Mode: Select whether the broadband wireless router operates without any security mode or with WEP, WPA and WPA-PSK mode. WPA-PSK Pass phr

54 Radius Server: Enter the Radius (Remote Authentication Dial-In user Service) server IP address. Radius Server Port: Enter the Raduis server port n

55 Host Name: Enter a hostname if it was provided by the ISP (Default: Wireless_Router). Domain Name: Enter a Domain Name if it was provided by the I

56 Cable Modem: If your broadband wireless router connects to the cable modem, click Cable Modem to enable/disable the MAC cloning function (MAC addr

57 3.12 Help Click Help on the Top-right button of each Web-based Utility section to connect Help screen. On the Help screen, you can see each Web

58

5• Simple Configuration: All default settings can be changed easily. LAN Features • 4-Port Ethernet switch : The Wireless Router provides 4 10/10

59 3.13 Logout Click Logout in the task bar to initiate wireless broadband router logout process. Click OK to logout the wireless broadband rou

604. Troubleshooting This chapter covers some common problems that user may encounter while accessing the wireless router and some possible solutions

61Q4) My PC can not locate the wireless router. Ans: Check the following. a) If your PC is set to Infrastructure Mode, because the router is alway

6 1.3 LEDs Indication & Connectors of Wireless Router Front Panel LEDs Indication LED Light Status Description PWR On Off Wireless Router i

7 1.4 System Requirements • One or more PCs (desktop or notebook) with Ethernet interface. • TCP/IP protocol must be installed on all PCs. • Ha

8 2 PC Configuration User needs to configure TCP/IP network settings, Internet access configuration and Wireless configuration for each sys